Vous n'êtes pas identifié.
Pages: 1
Bonjour,
Je voudrai savoir comment faire pour que SurperTrafficBoard puisse prendre en compte Ultimate Traffic 2 sur Prepar3D V2.5.
Dernière modification par Marcstrasb (04-11-2015 22:45:30)
Hors ligne
Bonjour,
Je suis en contact avec Flying W Simulation concernant le problème. Si jusqu'à présent j'arrivais à comprendre avec Google Translate, aujourd'hui je désirerai que quelqu'un maitrisant bien l'anglais puisse me donner le sens exact du dernier alinéa :
" Hello Marc
When I checked this problem again, I see you are trying to use UT2 and Prepar3D. That's not a supported configuration, I'm sorry I should have seen this earlier. The UT2 support is disabled in STB for Prepar3D.
That said, I can tell you how to turn it on, however I cannot provide any support should there be any problems with it. If you can agree those terms, I will send the information.
Regards
Simon "
Cordialement,
Marc
Hors ligne
Bonjour,
"Ceci dit, je peux vous dire comment le faire fonctionner, cependant je ne peux assurer aucun support en cas de problème avec cette procédure. Si vous accepter ces termes, je vous enverrai l'information."
Dernière modification par D5Turbi (04-11-2015 14:01:16)
Hors ligne
Merci Jean pour ton aide
Cordialement,
Marc
Hors ligne
Pas de quoi. J'en ai profité pour corriger la grosse faute de conjugaison.
Hors ligne
Hello Simon
Thanks a lot for your help ! The construction of files like you said and recommended by manipulations you have been successful !
I can now see the various traffics in STB.
Thanks again !
Regards,
Marc
Hors ligne
Marc
Simon du Team STB a t'il fourni une méthode pour faire fonctionner UT2 avec STB sous P3D V3.4 sans support comme j'ai pu le lire ?
Faut'il lui adresser directement un mail ?
Merci
Antigua
Hors ligne
Bonjour,
Je vais essayer de retrouver l'échange que j'ai eu avec le Team STB.
Trouvé :
Hi Marc,
Here's the procedure. Of course you can ask questions and I try to help, but there may not be much I can do. Flight1 does not support UT2 in P3D, but it seems to work also. The same is true for STB.
How to Activate UT2 Support in STB for P3DNavigate to the STB for P3D Application Data Folder%appdata%FlyingWSimulation\SuperTrafficBoard3\Prepar3D V2”%appdata%FlyingWSimulation\SuperTrafficBoard3\Prepar3D V3”Locate file “TrafficBoard.ini” and edit it. If it does not already exist, create it first.Add then following lines:[UT2 AI Supported]TRUESave the file and restart STB. You will need to rerun the configuration wizard to configure UT2 and STB for operations together. How to Activate UT2 Support in STB Data Server for P3DNavigate to the STB for P3D Application Data Folder%appdata%FlyingWSimulation\ STB Data Server\Prepar3D V2”%appdata%FlyingWSimulation\ STB Data Server\Prepar3D V3”Locate file “TrafficBoard.ini” and edit it. If it does not already exist, create it first.Add then following lines:[UT2 AI Supported]TRUESave the file and restart STB-DS. You will need to rerun the configuration wizard to configure UT2 and STB for operations together.
Traduction par Google Translate :
Voici la procédure. Bien sûr, vous pouvez poser des questions et j'essayer d'aider, mais il ne peut pas être beaucoup plus que je peux faire. Flight1 ne supporte pas les UT2 en P3D, mais il semble fonctionner aussi. La même chose est vraie pour le décodeur.
Comment activer UT2 Soutien au STB pour P3DNavigate au STB pour le dossier de données P3D application% appdata% FlyingWSimulation \ SuperTrafficBoard3 \ Prepar3D V2 "% appdata% FlyingWSimulation \ SuperTrafficBoard3 \ Prepar3D V3" Localisez le fichier "TrafficBoard.ini" et le modifier. Si elle n'existe pas déjà, créez first.Add puis en suivant les lignes: [UT2 AI pris en charge] TRUESave le fichier et redémarrez STB. Vous devrez relancer l'assistant de configuration pour configurer UT2 et STB pour les opérations ensemble. Comment activer le support UT2 Serveur STB données pour P3DNavigate au STB pour le dossier de données P3D application% appdata% FlyingWSimulation \ STB Data Server \ Prepar3D V2 "% appdata% FlyingWSimulation \ STB Data Server \ Prepar3D V3" Localisez le fichier "TrafficBoard.ini" et le modifier. Si elle n'existe pas déjà, créez first.Add puis en suivant les lignes: [UT2 AI pris en charge] TRUESave le fichier et redémarrez STB-DS. Vous devrez relancer l'assistant de configuration pour configurer UT2 et STB pour les opérations ensemble
Marc
Dernière modification par Marcstrasb (29-09-2016 18:58:30)
Hors ligne
Pages: 1